Updated : Oct 14, 2019 in Photos


ARMY TM &P* AIR FORCE TO 11W TECHNICAL M68 SIGHT, REFLEX, W/QUICK RELEASE MOUNT AND SIGHT MOUNT M68 Cco Tm Manual Army – p s – scribd TM. CHAPTER I. PRESENTATION. Aimpoint CompM4 Reflex Sight is a rugged precision red dot Sight developed mainly for military and law enforcement. M68 SIGHT, REFLEX, W/QUICK RELEASE MOUNT AND SIGHT MOUNT CLOSE COMBAT OPTIC (CCO) (NSN ) (NSN ).

Author: Kaktilar Kajilmaran
Country: Czech Republic
Language: English (Spanish)
Genre: Software
Published (Last): 7 May 2014
Pages: 389
PDF File Size: 11.55 Mb
ePub File Size: 18.16 Mb
ISBN: 974-4-90148-241-2
Downloads: 86112
Price: Free* [*Free Regsitration Required]
Uploader: Malalkis

Depot is the lowest level that can do complete repair of the item.

The M68 is from a family of sights known as reflex- or red-dot sights. However, if the battery is not installed correctly, there is a potential for a short circuit. Insert O-ring 3 around battery cap housing 2. CAUTION Before installing battery cap, inspect threads on battery housing and battery cap to ensure that they are free of moisture and dirt and that the O-ring in hm battery cap is present. Find the figure covering the functional group or the subfunctional group to which the item belongs.

The work packages provide such information as additional references i.

The M68 Close Combat Optic |

Government agencies and their contractors. The Comp M4 adjustment caps have straps and battery cap has an O-ring that keep out moisture. However, the complete NSN should be used when ordering items by stock number. Turn switch knob 6 clockwise and look through rear lens. To verify serviceability by measuring the mechanical, pneumatic, hydraulic, or electrical characteristics of an item and comparing those characteristics with prescribed standards on a scheduled ttm, i.

  IEC 60060-1 PDF

The OFF position is the same as the lowest night vision setting. See WP 00, pagefor installation procedures for spacer. There are three main causes for this condition. Right here, if this is the first time you are using this TM.

Army Publishing Directorate

Column 2 – Remarks. If the same sight is installed in the same position on the rail on the same weapon, re-zeroing is not required. No centering is required.

Both afloat and ashore intermediate levels are capable of complete repair of item. Gives you the number of the item illustrated. Part numbers of bulk materials are referenced in this column in the line entry to be manufactured or fabricated. Using tools to tighten mounting hardware could damage equipment.

Install sight assembly 1 on mounting rail 2.

The M68 Close Combat Optic

It normally consists of inspecting, servicing, lubricating, adjusting, and replacing parts, minor assemblies, and subassemblies. The special shaped spacer 7 does not have a front or back. The recommended location is with the front end of the mount lined up with front end of the upper receiver.

It provides Soldiers the ability to fire with one or two eyes open, as needed for the engagement sequence in the shot process. Note ccl figure and item number next to the NSN. The color indicating primary use is applied, preferably, to the entire exterior surface as the background color of the item. Cvo adjustment caps are easier to remove, and are protected against impact.

Open front cover 3adjust intensity with target background. This is necessary since figures are prepared for assembly groups and subassembly groups, and lists are divided into the same groups. Checks and services are numbered in disassembly sequence. To move point of impact up, turn elevation adjustment screw counterclockwise.


Column 2 – Maintenance Level. It uses a red aiming reference collimated dot and is designed for ,68 two eyes open method of sighting.

Before Sight Red dot is not Ensure that red dot is visible when switch knob is set to one visible. If the spring connector becomes corroded, clean it with a wire brush. Report all discrepancies in accordance with applicable service instructions e.

Consists of comparisons of two instruments, one of which is a certified standard of known accuracy, to detect and adjust any discrepancy in the accuracy of the instrument being compared.

Turn switch knob 2 to OFF position counterclockwise. WP 00 16 pages Items are returned to the supply sytem after mantenance is performed coc this level. Red dot does not appear. They are authorized to the level indicated by the code entered in the third position of rm SMR code. Navy only Reparable item. The maintenance code entered in the third position will indicate authorization to the following levels of maintenance: Install sight mount 1 on M16A2 rifle handle using O-ring 2 and mounting bolt 3.