Buy Gefran PID Temperature Controller, 48 x 48 (1/16 DIN)mm, 3 Output Relay, Also featuring soft start as well as an auto and manual function, the . View and Download Gefran user manual online. SINGLE DISPLAY TEMPERATURE CONTROLLER WITH UNIVERSAL INPUT. Temperature Controller. Gefran Pdf User Manuals. View online or download Gefran User Manual .
|Published (Last):||4 January 2010|
|PDF File Size:||18.37 Mb|
|ePub File Size:||15.96 Mb|
|Price:||Free* [*Free Regsitration Required]|
The HB alarm can be activated only with ON times longer than 0. The board is automatically recognized by the instrument, which enables display and setting of the parameters involved. As regards electromagnetic compatibility, the strictest generic standards have been adopted, as indicated in the table below. In the proximity gferan high frequency generators or arc welders, use adequate mains filters.
The peculiar characteristic of these transformers is the high number of secondary turns.
Gefran 400 User Manual
PL hotc. Turn on the instrument again B. Connect with the instrument powered and with inputs and outputs not connected. It is also possible to set an alarm point related to the current transformer input in order to check eventual load malfunction.
Default Custom 0 S. ALn is forced to 1 only for mod. It is essential that the plant has a good earth connection: The alarm limit setting is A. The power supply lines must be separate from the instrument input and output ones. Geffan a 1N diode in parallel with the coil of the inductive loads that operate in Direct Current.
Download file – link to post. For technical specifications and performance details refer to Section 13 “Technical Specifications”. X Maximum limit heating power 0, The variable for example, temperature must be that assumed at zero power room temperature. All the programming procedures of the instruments are facilitaded by the grouping of the parameters in function blocks CFG for the control parameters, Inp for the inputs, Out for the outputs, etc.
Single display controller – Gefran
For more information click here. To print the manual completely, please, download it. If the response is too slow, reduce it. C Switch to automatic and observe the behavior of the variable. Fix the device with the bracket provided before making any electrical connections.
S Digital filter on main input 0, The main input for the gefraan variable is universal and provides the possibility to connect many types of input sensor:. The type of input is selected from the faceplate keys and no external shunts or adapter are required.
The same time has to run after one-shot. Deviation indicator On if deviation is between 0. Default Custom 0 aI. OUT3 dans l’outil To mount two or more devices side by side, use the cut-out dimensions shown above.
S Minimum limit of main input scale min A configurable personal software protection code password protection can be used to restrict the levels of editing and displaying the configuration parameters. It therefore contains essential information for correct programming and configuration of the controllers. When finished, the Stun code is automatically cancelled. S Maximum limit of main input scale min The warranty excludes defects caused Power supply cable 1 mm Relay output cables 1 mm 3,5 m by any use not conforming to these instructions.
Set the setpoint to the required value 4. There is a link for the thermocouple NiCr Ni, type K on the front plate. This manual also for: Adatta a pilotare ingressi logici, applicazione tipica per interfaccia verso interruttori statici GTS. L Upper limit for local setpoint and absolute alarms Lo.
Process 400 display PV 2 sec. RTD 3 wires 16 17 Max. It is also possible to set an alarm point related to the current transformer input in order to check eventual load malfunction.
GEFRAN USER MANUAL Pdf Download.
When the electronic instrument power supply is strongly disturbed by the commutation of transistor or power units or motors, an isolation transformer should be used for the controllers only, earthing mqnual screen. Setting a limit of A. All the programming procedures of the instruments are facilitated by the grouping of the parameters in function blocks Manuxl for the control parameters, Inp for the inputs, Out for the outputs, etc.
Got it, continue to print. Documentation – Previous versions.
SP Cooling setpoint relative to heating set Panel mounting, extractable from front. If an oscillation persists, increase the proportional band. The main input for the process variable is universal and provides the possibility to connect many types of input sensor: Short Operating Instruction for temperature regulator We deliver our temperature regulator in its basic adjustment for the control of heaters.