Updated : Oct 11, 2019 in Photos


Small Spot/Mark (Separate Amplifier) Extremely thin beam ideal for detection of minute objects and marks. Order Omron Automation and Safety E3C-VS1G (ZND) at DigiKey. Check stock and pricing, view product specifications, and order online. Omron E3C-VS1G Photoelectric Sensor 10mm for E3C Amplifier: : Industrial & Scientific.

Author: Mejinn Grokree
Country: Oman
Language: English (Spanish)
Genre: Environment
Published (Last): 28 July 2007
Pages: 349
PDF File Size: 4.57 Mb
ePub File Size: 18.84 Mb
ISBN: 447-2-43937-189-8
Downloads: 89403
Price: Free* [*Free Regsitration Required]
Uploader: Meztijind

EE11 Check the parallel movement distance range in the catalog, verify the set distance between adjacent Sensors, and install the Sensors accordingly at a distance at least 1.

Hold the connector cover to connect or disconnect the connector. Through-beam Sensors Reflective Sensors 1 If Sensors are mounted in close proximity, use Sensors with the interference prevention function.


Omron E3c-vs1g E3CVS1G Photoelectric Sensor Switch | eBay

E3c-vs1 Sensors to distance where interference does not occur. Do not use it for such purposes. The lens, however, is plastic.

Nuclear energy control systems, combustion systems, railroad systems, aviation systems, medical equipment, amusement machines, vehicles, safety equipment, and installations subject to separate industry omro government regulations. These Sensors are designed for use in applications for sensing workpieces and workers that do not affect safety.

This is because the Sensors may affect each other and cause output chattering even if separated by more than e3c-fs1g Sensor sensing distance. Typical examples include the minimum sensing object, engineering data, step height detection data, and selection list for specifications.

M8 and M12 Connectors? Outdoor use, uses involving potential chemical contamination or electrical interference, or conditions or uses not described in this catalog. Mutual Interference Prevention Polarizing Filter: AC Two-wire Sensors Example: Power Supply Types An unsmoothed full-wave or half-wave rectifying power supply cannot be used.


AC 2-wire Sensors Example: Do not subject a shielded cable or coaxial cable to tension. This information by itself is not suf? For bending-resistant cable, see Attachment to Moving Parts e3c-v1sg page C The axis perpendicular to the center of the lens.

Doing so may cause explosion or burning.

The axis from the center of the lens to the center of the beam for the Emitter omfon the axis from the center of the lens to the center of the reception area for the Receiver.

Light may enter even if the Sensors are separated by more than the sensing distance.

Omron E3CVS1G Photoelectric Sensor, 10 mm Reflective, NPN Output Buy from Cross

Precautions for Correct Use Do not use the product in atmospheres or environments that exceed product ratings. Cable Tensile Strength When wiring the cable, do not subject the cable to a tension greater than that indicated in the following table. Use the following methods to attach and remove Fiber Units. If the connector is not connected securely, the connector may be disconnected by vibration or the proper degree of protection of the Sensor may not be maintained.

Keep organic solvents away from the Sensor. Refer to the values in the above table to check bend-resistant performance under actual working conditions. Secure the connector cover by hand. Precautions for Safe Use To ensure safety, always observe the following precautions.

To maintain the fiber characteristics, make sure that the lock is released before removing the fibers. However, if the workpieces are close to the Photoelectric Sensors, light from the adjacent Emitter may be received and cause the Sensor to change to the incident light state. The following measures can be taken to avoid mutual interference.


OMRON E3C-VS1G Photoelectric sensor

This may weaken performance. Be sure to connect or disconnect the connector after turning OFF the Sensor. Insert a capacitor, etc. If the Sensor does not operate, check the following points. Power line Work Required for Unconnected Leads Unused leads for self-diagnosis outputs or other special functions should 3ec-vs1g cut and wrapped with insulating tape to prevent contact with other terminals.

Fiber e3c-vsg mark Fiber 9mm 2 Removing Fibers Open the protective cover, lift up the lock lever, and pull out the fibers.

Please know and observe all prohibitions of use applicable to the products. This is omro intended to be an exhaustive list of all possible uses of the products, nor is it intended to imply that the uses listed may be suitable for the products: Typical measures are as given in the following table.

Organic solvents will dissolve the surface.

The Reflector cannot be mounted if there is any oil or dirt remaining. Placing them in the same conduit or duct may cause damage or malfunction due to induction interference. omro

Dirt should be gently wiped off with a dry cloth. They are rather values from samples taken from production lots, and are provided for reference as guidelines. If Sensors are mounted in opposite each other, slant omrom Sensors as shown in the following diagram. When in doubt, special model numbers may be assigned to?

Doing so may result in damage from burning and fire, particularly if the liquid is flammable.