Updated : Oct 24, 2019 in Music

CCNP SWITCH 6.0 INSTRUCTOR LAB MANUAL PDF

CCNP SWITCH 6 – BitRadius. Instructor Lab Manual Book everyone. Download file Free Book PDF Ccnp Switch Instructor Lab Manual at. CCNP: Implementing Secure Converged Wide-area Networks v – Lab Copyright © Ensure that the switch is set up so that both the router and host are in the same. VLAN. .. Figure Internet Explorer Security Alert Prompt. ccnp switch instructor lab pdf. CCNP SWITCH Instructor Lab Manual. This document is exclusive property of Cisco Systems, Inc.

Author: Meztira Manos
Country: Kazakhstan
Language: English (Spanish)
Genre: Personal Growth
Published (Last): 27 October 2013
Pages: 299
PDF File Size: 15.62 Mb
ePub File Size: 9.13 Mb
ISBN: 938-3-34303-349-5
Downloads: 86203
Price: Free* [*Free Regsitration Required]
Uploader: Maura

ALS1 config port-channel load-balance src-dst-mac c.

Which switch is the root of the spanning tree? Verify the access layer auto QoS configuration.

This product is part of the following series. ALS1 config ip sla responder udp-echo ipaddress The number of VTP servers should be consistent based on the amount of redundancy desired in the network.

This can lead to a denial of service or traffic interception. Be sure to save your final device configurations to use with the next lab. The output should be similar to the following sample for ALS1. If you are unable to comply with U. Set up these ports as static access ports and activate spanning-tree PortFast.

Verify that the configurations from Lab are loaded on the devices by issuing the show vtp status command. A unidirectional link occurs when traffic is transmitted between neighbors in one direction only.

  2052 RANDERS PDF

CCNP SWITCH Lab Manual, 2nd Edition

Issue the vlan command in global configuration mode on DLS1. Another way of changing which port becomes the root is to modify the port costs using the interface command spanning-tree cost cost. Verify the auto QoS configuration at the access layer using the show mls majual interface interface-type interface-number and show run commands.

FOC Power supply serial number: The first prompt asks for a hostname. If you are in a configuration mode, type exit or end.

If more routers share the highest priority, the HSRP router with the highest IP address on the segment becomes the active router. Which router is the active router for VLANs 1 and 10?

Cable the equipment as shown. Verify the configuration for ALS2 using the show port-security interface command. When the WLAN controller has finished restarting, log in with the username cisco and password cisco.

Optional Set an enable secret password and configure the vty lines for Telnet access to the switch. The default mode on a or is dynamic auto; the default mode on a or is dynamic desirable. How many of these are defaults? These switches can be used to manage all other switches in the VTP domain.

The switch might log messages to the console, such as interfaces coming up and down. When a new link becomes active, the port goes through the IEEE In either case, the network can be secured against such a disruption.

  JEAN BAUDRILLARD TRANSPARENCY OF EVIL PDF

To enable BPDU guard on PortFast-enabled ports, use the spanning-tree portfast bpduguard default global configuration command. The default configuration on switches is no ip routing. Set a default gateway with the default-router address command.

As a result, the designated switch does not send BPDUs. However, the VLAN database is still accessible for those who choose to use it. OK Number of successes: Identify the root bridge, root forwarding ports, designated forwarding ports, and alternate blocking ports.

ccnp-switch-instructor-lab-manual-slm

DLS1 show standby brief P indicates configured to preempt. However, the switches used in this lab do not support PoE.

Also, the directly- connected network Another way of creating VLANs is to create them in configuration mode without assigning port membership. The aaa authentication dot1x default local command tells instructir switch to use a local database of usernames and passwords to authenticate the users.

Optional To reset the WLAN controller, use the clear controller command followed by the reset system command. Each port has a default cost value based on a guideline established as part of IEEE