free pdf instructions. Find the office and computer equipment manual you need at ManualsOnline. Lexmark CN Printer User Manual. Page 1. Page 2. Following pdf manuals are available: Lexmark CN Installation Instruction, Reference Guide, User Manual. Service Manual. xx, 4xx. Go Back. Previous. Next. Assembly 1: Covers . 4. 3. 1. 6. 5. 8. 7. 2. 9 www MK-Electronic de.
|Published (Last):||3 March 2013|
|PDF File Size:||12.54 Mb|
|ePub File Size:||14.50 Mb|
|Price:||Free* [*Free Regsitration Required]|
Repeat these steps for every file you are updating on the printer. US fed as well as non-recycled paper.
First transfer Page – Step 4b: Prints the Print Alignment Pages and requires that the best line in each set of lines must be selected. Remove the cable mannual A.
Lexmark C540n C543dn C544 series service manual download
Checking the status of supplies from a network computer. Moving the printer to another location. Replace the controller shield. The printer performs a POR, and returns to normal mode.
Once the printer has been restored to its default levels, do the following: Remove the rear screw A in the waste toner bottle sensor contact to allow access to the c540j cover. Replace the For example, the distance between these two Replace the Close door Message clears when front cover, right cover, and toner door are closed or securely fastened. An optional memory card that can be plugged into an available memory slot.
Printing a network setup page. The USB port cable G is not included. Imaging Kit The following actions can be taken: To change the Defaults: C54n0 very careful disconnecting handling the ribbon cable.
LEXMARK CN SERVICE MANUAL Pdf Download.
Page xx, 4xx Service Manual Remove the three screws D securing the lower right manua, to the printer. Lexmark C54x Series User Manual pages. Disconnect the cable A from the fuser drive motor assembly. Remove the four short screws A in front, and the four longer screws B in the back of the duplex aligner. Remove the right cover assembly. Remove the two screws G on the right of the main drive gear assembly Lift the main drive gear assembly, and remove. To print the manual completely, please, download it.
For mmanual color, the toner cartridge engages the photoconductor so it applies toner to the surface. Frames Page Page – Assembly 3: Rear Shield Removal xx, 4xx Detach the operator panel cable C from the panel. Page xx, mahual Next to screw Elift the right lower frame pin F out of the hole in the printer frame.
The line that best matches the defects on the print job indicates which particular part may be causing the defect.
Lexmark C540n Service Manual
Theory Of Operation xx, 4xx Theory of operation Print engine theory Electrophotographic process EP process The method that all laser and LED printers use to print is called the electrophotographic process. When factory default settings are restored: First Transfer xx, 4xx Step 4a: Page xx, 4xx Next to screw Dlift the right lower frame pin E out of the hole in the printer frame.
Press each operator panel button, and watch to see if the count of button presses increases by one for each press. Open the toner supply door. Page xx, 4xx Be sure the shaft and bearing have not shifted out of c540 guide.
Lexmark CN manuals |
Always use paper between and Sheffield points; however, smoothness between and Sheffield points produces the best print quality. To run the Button Test: Paper and specialty media guide.
Other menu items may only be effective for a particular printer language.
Release the latches Aand lift off the cover. Page 65 – Networking service check Page 66 Page 67 – Operator panel service check Page 68 – Operator panel display blank, five beeps Page 69 – Operator panel display blank, printer be Page xx, 4xx Remove the manuao screws B.
User Operator Panel And Administration Menus xx, 4xx User operator panel and Administration menus Printer operator panel The printer operator panel has a two-line, back lit, grayscale text display. Remove the rubber pad C. Installing the printer on a wireless network Windows.
Rotate the top of the fuser toward the front, then slide it to the left to align the fuser side frames with the flat areas of the shaft Fand lift to remove the fuser.
Make sure the shaft on the left side aligns with the hole in the frame.