Updated : Oct 07, 2019 in Photos

AIRLIVE WL-5450AP PDF

WLAP repeater mode is WDS repeater, so it can connect other wireless device with MAC address. So you can set another station in Bridge mode. AirLive WLAP, WLAP is in conformity with. In accordance with 93/68/ EEC Directive and /5 EC-R & TTE Directive. Clause. Description. The WLAP and WLAP uses different firmwares. Please do not use the wrong firmware (i.e. do not use WLAP firmware on.

Author: Tegrel Shakazuru
Country: Vietnam
Language: English (Spanish)
Genre: Health and Food
Published (Last): 20 February 2007
Pages: 283
PDF File Size: 6.27 Mb
ePub File Size: 1.57 Mb
ISBN: 999-1-13968-413-3
Downloads: 41604
Price: Free* [*Free Regsitration Required]
Uploader: Tygosida

Status Turns solid red when the device is booting, after boot successfully, the light turn off. Usually, the best place for the Access Point is at the center of your wireless network, with line of straight to all your wireless stations. Table Of Contents Introduction Advanced Settings Advanced Settings It is not recommended that settings in this page to be changed unless advanced users want to change to meet their wireless environment for optimal performance Authentication Type To provide a certain level of security, the IEEE Other Upgrade Firmware 1.

If you want to change the settings in order to perform al-5450ap advanced configuration or even change the mode of operation, you can use the web-based utility provided by the manufacturer as described in the following sections. Comments to this Manuals Your Name.

Airlive / Ovislink WL-5450AP

Status Status In this screen, you can see the current settings and status of this Access Point. Other Other Upgrade Firmware 1. In the Address box, enter the following: This manual also for: Users can use this feature to build up a large wireless network in a large space like airports, hotels and schools …etc.

  BUKU WATIR PDF

Security Here you can configure the security of your wireless network. wl-54550ap

Download AirLive WLAP Access Point Firmware eu for OS Independent

Don’t have an account? Security Security Here you can configure the security of your wireless network.

Two APs in bridge modes can communicate with each other through wireless interface. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

Selecting different method will enable you to have different level of security. Make sure your wired station is set to the same subnet as the Wireless Access Point, i. Wireless Basic Settings This page includes all primary and major parameters. An SSID is also referred to as a network name because essentially it is a name that identifies a wireless network.

Don’t show me this message again. Performing the Factory Reset will erase all previously entered device settings. Password Password For secure reason, it is recommended that you set the account to access the web server of this Access Point.

SG :: Airlive / Ovislink WLAP Wireless Access Point

Before you starting hardware connection, you are advised to find an appropriate location to place the Access Point. This device is shipped with configuration that is functional right out of the box. Disabled IP Address Data Rate By default, the unit adaptively selects the highest possible aidlive for transmission. Client Mode Ad-hoc If set to the Client Sl-5450ap mode, this device can work like a wireless station when it is connected to a computer so that the computer can send packets from wired end to wireless interface.

  DENISOV CLARINET SONATA PDF

Also, remember to adjust the antenna; usually the higher the antenna is placed, the better will be the performance. Got it, continue to print. You may enter up to 20 characters wl-5405ap a remark to the previous MAC Address. Page 33 Save Settings to Aiirlive Any parameter change will cause the device to reboot for the new settings to take effect. If your system manager assigned you static IP settings, then you will have to enter the information provided.

Page 23 Before a station enters power save mode, the station needs the beacon interval to know when to wake up to receive the beacon and learn whether there are buffered frames at the access point. You can change settings by selecting specific tab described in below.

To print the manual completely, please, download it. These limits are designed to provide reasonable protection against harmful interference in a residential installation.